DIY Guide: Disassembling the Detergent Dispenser in Your Splendide Washer-Dryer
WD2100XC / XCP (Splendide 2100XC) WDC7100XCP (Splendide 7100XC)
Is your Splendide washer-dryer not dispensing detergent properly or leaking around the dispenser area? If so, it may be time to clean or repair the detergent dispenser assembly. This guide will walk you through the process of safely disassembling and inspecting the dispenser to keep your washer-dryer in peak condition.
Tools Needed:
- Phillips head screwdriver
- Flathead screwdriver
Step 1: Power Off the Washer-Dryer
Before beginning any disassembly, make sure to unplug the unit from the power source or switch off the circuit breaker. This ensures your safety when working on the appliance.
Step 2: Remove the Washer-Dryer Top Panel
To access the detergent dispenser assembly, you need to first remove the top panel of the washer-dryer. Using your Phillips head screwdriver, remove the screws that secure the top panel to the back of the machine. Once the screws are removed, slide the top panel backward slightly and lift it off.
This step gives you access to the internal components, including the detergent dispenser.
Step 3: Remove the Detergent Drawer
Open the detergent drawer and pull it out as far as it will go. Then, press the small tab located at the back of the drawer and pull it out completely from the housing. This will give you a clear view of the screws securing the detergent dispenser assembly to the control panel.
Step 4: Detach the Detergent Dispenser Assembly
With the drawer removed, you will see three Phillips head screws securing the front of the detergent dispenser to the control panel. Remove these screws.
Next, remove the two screws that hold the detergent dispenser assembly to the water valves at the back of the housing. You may need to disconnect some wires connected to the hot valve, so remember to take note of their positions to reattach them later.
Step 5: Disconnect the Dispenser Hoses
The detergent dispenser is connected to hoses that carry water and detergent into the washer. Locate the hose connected to the dispenser and carefully pull the loop off to the side. Once removed, the hose can be gently pulled straight off the dispenser assembly. Be cautious not to damage the hose during this step.
Step 6: Inspect and Clean the Dispenser Assembly
With the detergent dispenser removed, take the opportunity to inspect it for any clogs, buildup, or damage. Rinse out the dispenser under running water to remove any detergent residue. If you find cracks or damage, you may need to replace the entire dispenser assembly.
Step 7: Reassemble the Washer-Dryer
Once the detergent dispenser is cleaned or repaired, it’s time to put everything back together. Reattach the dispenser hoses, ensuring they are firmly connected to avoid any leaks. Then, secure the detergent dispenser assembly to the control panel with the screws you removed earlier.
Next, reattach the dispenser drawer by sliding it back into the housing until it clicks into place. Finally, replace the washer-dryer’s top panel and secure it with the screws.
Step 8: Test the Dispenser
Plug the washer-dryer back into the power source and run a test cycle. Make sure the detergent is dispensing correctly and there are no leaks around the dispenser. If everything is working as expected, your Splendide washer-dryer is ready for regular use again!
Final Tips:
- Prevent future clogs by regularly cleaning the detergent drawer and dispenser assembly to remove detergent residue.
- Be mindful of the hose connections during reassembly, as improperly attached hoses can lead to leaks.
By following these steps, you can easily disassemble, inspect, and clean your Splendide washer-dryer’s detergent dispenser. Regular maintenance can prevent bigger problems down the line and keep your appliance running smoothly
This guide provides a simple, straightforward solution for maintaining and repairing the detergent dispenser in your Splendide washer-dryer, helping to avoid leaks and ensure proper detergent flow.